Anyone attempt this conversion. Just curious.
I have a good sd22 motor and the 22re in my toyota needs major work. Big undertaking? :
________
Silver Surfer Vaporizer
sd22 into an 89' toyota 4x4?
Moderators: goglio704, Nissan_Ranger
-
- Posts: 1
- Joined: 16 years ago
-
- Posts: 121
- Joined: 17 years ago
- Location: Greenville South Carolina
It might be a little late, but this guy mated the w56 to the SD22. He is one of the best fabricators I have ever seen too.
http://board.marlincrawler.com/index.ph ... ;topicseen
http://board.marlincrawler.com/index.ph ... ;topicseen
1992 nissan pathfinder 4x4
1985 KC 720 4x4
1982 KC 720
1985 KC 720 4x4
1982 KC 720
- asavage
- Site Admin
- Posts: 5436
- Joined: 18 years ago
- Location: Oak Harbor, Wash.
- Has thanked: 1 time
- Contact:
Welding the SD starter bellhousing cone to the Toy bellhousing is tough work. There is no provision to adjust the starter drive gear-to-ring gear clearance on either design, so positioning before welding is critical.
I read a few pages worth forward in that thread to see if he had problems with it later, but there are 113 pages in that thread, and when I hit the homophobic shit on page six I gave up . . . someone else will have to dig for the info.
I read a few pages worth forward in that thread to see if he had problems with it later, but there are 113 pages in that thread, and when I hit the homophobic shit on page six I gave up . . . someone else will have to dig for the info.
Regards,
Al S.
1982 Maxima diesel wagon, 2nd & 4th owner, 165k miles, rusty & burgundy/grey. Purchased 1996, SOLD 16Feb10
1983 Maxima diesel wagon, 199k miles, rusty, light yellow/light brown. SOLD 14Jul07
1981 720 SD22 (scrapped 04Sep07)
1983 Sentra CD17, 255k, bought 06Jul08, gave it away 22Jun10.
Al S.
1982 Maxima diesel wagon, 2nd & 4th owner, 165k miles, rusty & burgundy/grey. Purchased 1996, SOLD 16Feb10
1983 Maxima diesel wagon, 199k miles, rusty, light yellow/light brown. SOLD 14Jul07
1981 720 SD22 (scrapped 04Sep07)
1983 Sentra CD17, 255k, bought 06Jul08, gave it away 22Jun10.
-
- Posts: 121
- Joined: 17 years ago
- Location: Greenville South Carolina
It worked fine for him, he took that thing all over the country. However he did swap a toyota diesel into it later for more power. As I understand he built, or someone else has built more than one of those bell housings allowing use of the SD22 on a toyota tranny.
There is some pretty good stuff in there too, such as running a super charger on the SD22 and lots of turbo stuff.
There is some pretty good stuff in there too, such as running a super charger on the SD22 and lots of turbo stuff.
1992 nissan pathfinder 4x4
1985 KC 720 4x4
1982 KC 720
1985 KC 720 4x4
1982 KC 720
- asavage
- Site Admin
- Posts: 5436
- Joined: 18 years ago
- Location: Oak Harbor, Wash.
- Has thanked: 1 time
- Contact:
It didn't work fine by chance; he had to have done a good setup job, that's not easy. Not a procedure I'd recommend to someone who doesn't have excellent layout skills.bacho wrote:It worked fine for him . . .
Even aligned, it would still have to be faced (and probably bored) after welding, for long-term bearing reliability.
OTOH, an adapter plate might be fairly straightforward, at least for me. Maybe.
Who is online
Users browsing this forum: No registered users and 1 guest